MODEL REPRESENTATION OF THE SPRAY DRYING PROCESS OF THE DISTILLERY STILLAGE FILTRATE BASED ON NAVIERSTOKES EQUATIONS
https://doi.org/10.20914/2310-1202-2015-4-11-16
Abstract
Spray drying of solutions and suspensions is among the most common methods of producing a wide range of powdered products in chemical, food and pharmaceutical industries. For the drying of heat-sensitive materials, which is fully applicable to the distillery stillage filtrate continuous-flow type of contact of drying agent and the solution droplets is examined. Two-phase simulation method of computational hydrodynamics in a stationary state for studying the process of drying of the distillery stillage filtrate in the pilot spray dryer under the following assumptions was used. The components form an ideal mixture, the properties of which are calculated directly from the properties of the components and their proportions. The droplets were presented in spherical form. The density and specific heat of the solution and the coefficient of vapors diffusion in the gas phase remained unchanged. To solve the heat exchange equations between
the drying agent and the drops by the finite volume method the software package ANSYS CFX was used. The bind between the two phases was established by Navier-Stokes equations. The continuous phase (droplets of the distillery stillage filtrate) was described by the k-ε turbulence model. The results obtained showed that the interaction of "drop-wall" causes a significant change of velocity, temperature and humidity both of a drying agent and the product particles. The behavior of the particles by spraying, collision with walls and deposition of the finished product allowed to determine the dependence of physical parameters of the drying process, of the geometric dimensions of the dryer. Comparison of simulation results with experimental data showed satisfactory convergence of the results: for the temperature of the powder 10% its humidity of 12% and temperature of the spent drying agent at the outlet from the drier of 13%. The possibility of using the model in the spray dryers designing, and control of the drying process is shown.
the drying agent and the drops by the finite volume method the software package ANSYS CFX was used. The bind between the two phases was established by Navier-Stokes equations. The continuous phase (droplets of the distillery stillage filtrate) was described by the k-ε turbulence model. The results obtained showed that the interaction of "drop-wall" causes a significant change of velocity, temperature and humidity both of a drying agent and the product particles. The behavior of the particles by spraying, collision with walls and deposition of the finished product allowed to determine the dependence of physical parameters of the drying process, of the geometric dimensions of the dryer. Comparison of simulation results with experimental data showed satisfactory convergence of the results: for the temperature of the powder 10% its humidity of 12% and temperature of the spent drying agent at the outlet from the drier of 13%. The possibility of using the model in the spray dryers designing, and control of the drying process is shown.
About the Authors
A. A. Shevtsov
Voronezh state university of engineering technologies
Russian Federation
Department of technology of bread, confectionary, pasta and grain production department, professor
Russian Federation
Department of technology of bread, confectionary, pasta and grain production department, professor
A. S. Muravev
Voronezh state university of engineering technologies
Russian Federation
Department of technology of bread, confectionary, pasta and grain production department, post-graduate
Russian Federation
Department of technology of bread, confectionary, pasta and grain production department, post-graduate
References
1. 1 Aleksanyan, I. Yu., Maksimenko Yu. A., Feklunova Yu.S. Mathematical modeling of heat and mass transfer from spray drying of plant extracts Vestnik Astrahanskogo gosudarstvennogo tehnicheskogo universiteta. Serija: Upravlenie, vychislitel'naja tehnika i informatika. [Proceedings of Astrakhan State Technical University. Series: Management, Computer science and Informatics], 2013, no. 1, pp. 9–13. (In Russ.).
2. 2 Shevtsov A.A., Derkanosova A.A.; Korotaeva A.A. Muravev A.S. Modeling of the spray drying process of green protein suspension concentrate (PGC) Vestnik Voronezhskogo gosudarstvennogo universiteta inzhenernyh tehnologij [Proceedings of Voronezh state University of engineering technologies], 2015, no. 1 (63), pp. 51–57. (In Russ.).
3. 3 Shevtsov A.A. Solving the Boundary-Value Problem for Heat Conduction in a Granule Covered with a Solution Film in the Spray Drying Process Teoreticheskie osnovy himicheskoj tehnologii. [Theoretical foundations of chemical engineering], 2013, vol. 47, no. 6, pp. 630–633. (In Russ.).
4. 4 Ali M CFD modeling of a counter-current spray drying tower. International conference in multiphase flow. Jeju, South Korea, 2013.
5. 5 Mezhericher M., Levy A., Borde I. Three-Dimensional Spray-Drying Model Based on Comprehensive Formulation of Drying Kinetics Drying Technology. 2012, vol. 30, no. 11-12, pp. 1256–1273.
6. 6 Evgrafova A.V., Ibraev D.F., Suhanovskij A.N. Modeling of convective flows in CFD-packages Vestnik Permskogo universiteta. [Bulletin of Perm University], 2012, no. 3, pp. 37–41. (In Russ.).
7. 7 Laptev A.G., Farahov T.M. Mathematical models and calculation of the hydrodynamic characteristics of a boundary layer. Politematicheskij setevoj jelektronnyj nauchnyj zhurnal Kubanskogo gosudarstvennogo agrarnogo universiteta. [Multidisciplinary network electronic scientific journal of the Kuban state agrarian university], 2012, no. 82, pp. 12–47. (In Russ.).
8. 8 Ermakov M.K. Fiziko-himicheskaja kinetika v gazovoj dinamike. [Physical and chemical kinetics in gas dynamics], 2010, vol. 9, pp. 1–8. (In Russ.).
9. 9 Shevtsov A.A. Drannikov A.V., Mu-rav'ev A.S. mater. IV Mezhdunar. nauch-tehn. konf. [Proc of IV international sci-technical conf. "Innovations in technology and engineering of functional foods based on biomedical views]. Voronezh, VGUIT, 2014. pp. 741–744. (In Russ.).
10. 10 Aleksanyan I. Yu., Vasina N.P. Research of kinetics of drying of a sheeting of treatment-andprophylactic
11. food additives. Tekhnologii pishchevoi i pererabatyvayushchei promyshlennosti APKprodukty zdorovogo pitaniya. [Technologies of food and processing industry of agrarian and industrial complex products of healthy food], 2014, no. 4, pp. 62-67. (In Russ.).
Review
For citations:
Shevtsov A.A., Muravev A.S. MODEL REPRESENTATION OF THE SPRAY DRYING PROCESS OF THE DISTILLERY STILLAGE FILTRATE BASED ON NAVIERSTOKES EQUATIONS. Proceedings of the Voronezh State University of Engineering Technologies. 2015;(4):11-16. (In Russ.) https://doi.org/10.20914/2310-1202-2015-4-11-16
Views:
570
Email this article 
Post a Comment 
